"Digital DC Motor Drive V65D Series" utilizes the DSP technology and modular design, it could replace analog type dc motor drive completely, so V65D DC Motor Drive is very suitable for the refurbished market of the DC Motor Drive of traditional machinery, the application market of the power requirement of high-torque in low-speed.

Main Features

• Using the technology of DSP, control is accurate.

• The driving range for DC Motor is from 35A to 2,000A.

• Two-quadrant DC motor unidirectional control and four-quadrant DC motor forward and backward two-direction control.

• Selections of feedback signal, Armature voltage, ACTG or DCTG and Encoder.

• Auto detection and adjustment to Phase sequence (R-S-T).

• Regenerate type of brake, saving energy.

• Field weakening control.

• Magnetic loss, motor overload protection.

• Self- diagnosis function, maintenance is easy.

• Support RS-485 interface and MODBUS protocol.

TC-2050 & TC-2050P tension controllers use the feedback signal of high-precision LMS series of tension detectors to stabilize tension control. It uses two chips of 16 bits of the microprocessor to do computing division, having the performance of fast and stable tension control, and is suitable for tension control for unwinding/infeed, center proportional linkage, and rewinding / receiving.

Main Features

• The functions of unwinding / infeed, center proportional linkage, and rewinding / receiving can be set by the internal DIP switch of TC-2050/P.

• It includes the digital type of line-speed proportional linkage function, which can make line speed in accelerating or decelerating until the stop keeps stable tension control.

• Multi-level P.I.D, which can present a fast and stable function when speed is variable at any time.

• Large subtitles high brightness LED numeric display, which can be selected by the parameter “SRC” to display different units, such as kg.m/min, etc.

• The parameter function is symbolized by English abbreviations and can be easily operated without relying on the manual.

• There are LED window displays, “RUN” is for running, “CENTER” is for center proportional linkage, “WINDER” is for unwinding/rewinding, “SENSOR” is for the abnormal detector, “ERROR” is for the abnormal message.

• Working with LMS series of load cell, rated load of 5Kg ~ 1,000Kg (50NM～10,000NM).

TC-2010 receives tension detected signal from LMS series, PDS series of tension detector, built-in 16 bits high-speed microprocessor with the function of calculation, presenting fast and stable tension control performance.

Main Features

• It includes a digital type of line-speed proportional linkage function, which can maintain stable tension control from starting,accelerating, or decelerating to stopping.

• Multi-level P.I.D, which can present a fast and stable function when speed is variable at any time.

• Large subtitles high brightness LED numeric display, which can be selected by the parameter “SRC” to display different units, such as kg.m/min, etc..

• The parameter function is symbolized by English abbreviations and can be easily operated without relying on the manual.

• There are LED window displays, “RUN” is for running, “HIP” is for the high limit, “LOP” is for the low limit, and “ALM” is for the abnormal messages.

• The terminal that can receive a set of encoder or pulse signals is regarded as the source of the line-speed signal.

Edge Position Controller EPD-3008-A
EPD-3008 can accept an Ultrasonic or Infrared-type edge position detector to drive an electric cylinder and achieve material edge alignment.

Main Features

• Built-in DC motor feedback loop that can select a drive unit, which accepts feedback signal, and enhance the accuracy and response of edge alignment.

• Combining the operation panel and controller together can mount on the surface of a plate or externally stand-alone for operation.

• Accepting vary of Edge Position Detectors.

• Working to vary of drive units, such as EPM series electric cylinders.

• Built-in the loop of edge position output signal that can connect to the external high-capacity drive unit and enlarge drive capacity.

• Equipped with RS-485 communication that can connect to computers.

Edge Position Operator EPOP-03As a remote operation kit of Edge Position Controller EDP-3008P, it uses communication transmission to transmit operation instructions to Controller and display detector’s detected position on the operation panel.

Soft-start motor controller, used in the pump motor, hydraulic motor, pumping stations, water equipment, soft start and soft stop, so that the water pump motor system can eliminate water hammer, pipe will not let the noise affect the quality of the living.

Main Features

• Soft start time, start torque and soft stop time can be adjusted, let soft starter smooth.

• 3 starting ways can be choice in this machine: slope starter, current-limit starter, current-limit and kick starter.

• Use the S.C.R. control: No contacts, no arc, no wear and tear, the equivalent of semipermanent life.

• Various resolutions : up to 10-bit (1024 divisions)

• Wiring easy: installation of 3 in 3 out, save the coast of hand wiring.

• This controller is microprocessor with the function of automatic light/heavy loading revision and torque control.

• Cooling fans has temperature control, the cooling sheet working at 55C, and stop at 45C, this design can extend use-life of fans 2-3 times.

• The controller inside electronic sensor of CT: overload protection, input power loss the phase protection, motor block protection, controller over temperature protection, low load protection, exceed sensitive reaction, and no thermal effect, not affected by ambient temperature.

Soft-start motor controller, use the conveyor's motor, overhead cranes, soft start, reducing the instantaneous starting current. When the motor abnormality, can protect the motor.

Main Features

• Soft start time and start torque can be adjusted, let soft starter smooth.

• Start way: slope starter.

• Use the S.C.R. control: No contacts, no arc, no wear and tear, the equivalent of semipermanent life.

• Built-in reverse polarity protection circuit and output overcurrent (short-circuit) protection circuit

• Wiring easy: installation of 3 in 3 out, save the coast of hand wiring.

• This controller is microprocessor with the function of automatic light/ heavy loading revision and torque control.

• Cooling fans has temperature control, the cooling sheet working at 55C, and stop at 45C, this design can extend use-life of fans 2-3 times.

• The controller inside protection function: Input power loss the phase protection, controller over temperature protection, exceed sensitive reaction and no thermal effect, not affected by ambient temperature.